Kikusui KHA3000 Скачать руководство пользователя страница 328 | Manualshive

Страница: 328 / 392

Kikusui KHA3000 Скачать руководство пользователя страница 328

328

KHA3000

Querying Measurement Data

FETC:CURR:HARM:PHAS

READ:CURR:HARM:PHAS

MEAS:CURR:HARM:PHAS

Each queries the phase angle of harmonic current.

Command

FETCh[<channel#>][:SCALar]:CURRent:HARMonics:PHASe?

{ALL|<NRf>}

READ[<channel#>][:SCALar]:CURRent:HARMonics:PHASe?

{ALL|<NRf>}

MEASure[<channel#>][:SCALar]:CURRent:HARMonics:PHASe?

{ALL|<NRf>}

Parameter Value:

1 to 40 (harmonic measurement mode)
1 to 180 (FFT analyzer)

“ALL” queries data of all orders.

Response

Returns the phase angle of <NRf>th-order harmonic current in the <NR3> format for
FETC:CURR:HARM:PHAS? <NRf>, READ:CURR:HARM:PHAS? <NRf> and
MEAS:CURR:HARM:PHAS? <NRf>.
Returns the phase angles of harmonic current of all orders in the <NR3>, <NR3> ... format
for FETC:CURR:HARM:PHAS? ALL, READ:CURR:HARM:PHAS? ALL and
MEAS:CURR:HARM:PHAS? <ALL>.
Unit:

DEG

Querying a Momentary Flicker Value

FETC:FLIC:ST

READ:FLIC:ST

MEAS:FLIC:ST

Each queries a momentary flicker value.

Command

FETCh[<channel#>][:SCALar]:FLICker:ST?

READ[<channel#>][:SCALar]:FLICker:ST?

MEASure[<channel#>][:SCALar]:FLICker:ST?

Response

Returns the momentary flicker value in the <NR3> format.
Unit:

None

«
...
326
327
328
329
330
...
»

Содержание KHA3000









































































































































































































































































































































































































Отзывы:

Нет отзывов