Kikusui KHA3000 Скачать руководство пользователя страница 326

Страница: 326 / 392

326

KHA3000

Querying Measurement Data

Querying Current

FETC:CURR:AC

READ:CURR:AC

MEAS:CURR:AC

Each of these commands queries the measured value of the alternate current (rms).

Command

FETCh[<channel#>][:SCALar]:CURRent:AC?

READ[<channel#>][:SCALar]:CURRent:AC?

MEASure[<channel#>][:SCALar]:CURRent:AC?

Response

Returns the measured value of the alternate current (rms) in the <NR3> format.
Unit:

A(RMS)

FETC:CURR:AMPL:MAX

READ:CURR:AMPL:MAX

MEAS:CURR:AMPL:MAX

Each queries the measured value of the maximum current (positive amplitude peak value).

Command

FETCh[<channel#>][:SCALar]:CURRent:AMPLitude:MAXimum?

READ[<channel#>][:SCALar]:CURRent:AMPLitude:MAXimum?

MEASure[<channel#>][:SCALar]:CURRent:AMPLitude:MAXimum?

Response

Returns the measured value of the maximum current (positive amplitude peak value) in the
<NR3> format.
Unit:

FETC:CURR:AMPL:MIN

READ:CURR:AMPL:MIN

MEAS:CURR:AMPL:MIN

Each queries the measured value of the mimimum current (negative amplitude peak value).

Command

FETCh[<channel#>][:SCALar]:CURRent:AMPLitude:MINimum?

READ[<channel#>][:SCALar]:CURRent:AMPLitude:MINimum?

MEASure[<channel#>][:SCALar]:CURRent:AMPLitude:MINimum?

Response

Returns the measured value of the minimum current (negative amplitude peak value) in the
<NR3> format.
Unit:

Содержание KHA3000









































































































































































































































































































































































































Результаты поиска

Содержание KHA3000

Отзывы:

Kikusui KHA3000, Руководство по эксплуатации, Страница: 326 / 392

Результаты поиска

Содержание KHA3000

Отзывы: