manualshive.com logo in svg

Kikusui KHA3000, Руководство по эксплуатации, Страница: 324 / 392

Поделиться
Скачать
Kikusui KHA3000 Скачать руководство пользователя страница 324

324

KHA3000

Querying Measurement Data

FETC[<channel#>][SCALar]:<meas_item>

READ[<channel#>][SCALar]:<meas_item>

MEASure[<channel#>][SCALar]:<meas_item>

FETC

Queries measurement data without starting measurement operation.
If FETC? is sent without measurement, an SCPI error (-230, 

“

Data corrupt or stale

”

) occurs

because  no  measurement  data  is  available.  Always  use  this  command  with  the  INIT
command.
If  <meas_item>  is  not  specified,  the  value  set  by  previous  FETC?,  READ?  or
MEAS:<meas_item>? is used.

Command

FETCh[<channel#>][:SCALar][:<meas_item>]?

Response

Returns measurement data in the <NR3> format in response to FETC?.

READ

Queries measurement data after starting new measurement operation.
READ? works the same as the INIT command issued in combination with the FETC? query.
If  <meas_item>  is  not  specified,  the  value  set  by  previous  FETC?,  READ?  or
MEAS:<meas_item>? is used.

Command

READ[<channel#>][:SCALar][:<meas_item>]? 

Response

Returns measurement data in the <NR3> format in response to READ?. 

MEAS

Aborts the current measurement operation and starts the measurement operation anew, and
then queries measurement data.
MEAS:<meas_item>?  works  the  same  way  as  the  ABORT  command  combined  with  the
READ? query.

Command

MEASure[<channel#>][:SCALar]:<meas_item>?

Response

Returns measurement data in the <NR3> format in response to MEAS:<meas_item>?.

•

If measurement has not been completed yet immediately after transmission of the INIT 
command or the READ:<meas_item>? or MEAS:<meas_item>? query, the response data 
FETC:<meas_item>?, READ:<meas_item>? or MEAS:<meas_item>? query is generated 
after the completion of measurement.

Содержание KHA3000









































































































































































































































































































































































































Отзывы:

Нет отзывов