Kikusui KHA3000 Скачать руководство пользователя страница 316

Страница: 316 / 392

316

KHA3000

Voltage Fluctuation Measurement Mode (61000-
3-11)

Measurement Time, Measurement Count and Limit Values

VFL:IEC311:DMAX

Sets the limit value of dmax.

Command

VFLuctuation:IEC311:DMAXlimit {4|6|7}

VFLuctuation:IEC311:DMAXlimit?

Parameter Value:

4, 6 or 7 (The default is 6.)

Unit:

PCT

Response

Returns the limit value of dmax (maximum relative voltage changes) in the <NR3> format.

VFL:IEC311:PSTC

Sets the Pst measurement count.

Command

VFLuctuation:IEC311:PSTCount <NRf>

VFLuctuation:IEC311:PSTCount?

Parameter Value:

1 to 12 (The default is 12.)

Unit:

None

Response

Returns the Pst measurement count in the <NR3> format.

VFL:IEC311:PSTT

This command sets the Pst measurement time.

Command

VFLuctuation:IEC311:PSTTime {<numeric>|MIN|MAX}

VFLuctuation:IEC311:PSTTime?

Parameter Value:

30 to 900 (The default is 600.)

Unit:

Response

Returns the Pst measurement time in the <NR3> format.

** RST

RST

** RST

RST

** RST

RST

Содержание KHA3000









































































































































































































































































































































































































Результаты поиска

Содержание KHA3000

Отзывы:

Kikusui KHA3000, Руководство по эксплуатации, Страница: 316 / 392

Результаты поиска

Содержание KHA3000

Отзывы: