Kikusui KHA3000 Скачать руководство пользователя страница 313

Страница: 313 / 392

KHA3000

313

Rem

ote Control

Voltage Fluctuation Measurement Mode (61000-
3-3)

Measurement Time, Measurement Count and Limit Values

VFL:IEC33:DMAX

Sets the limit value of dmax.

Command

VFLuctuation:IEC33:DMAXlimit {4|6|7}

VFLuctuation:IEC33:DMAXlimit?

Parameter Value:

4, 6 or 7 (The default is 6.)

Unit:

PCT

Response

Returns the limit value of dmax (maximum relative voltage changes) in the <NR3> format.

VFL:IEC33:DCO

Sets the d measurement count.

Command

VFLuctuation:IEC33:DCOunt <NRf>

VFLuctuation:IEC33:DCOunt?

Parameter Value:

3 to 24 (The default is 24.)

Unit:

None

Response

Returns the d measurement count in the <NR3> format.

VFL:IEC33:DTIM

Sets the d measurement time.

Command

VFLuctuation:IEC33:DTIMe {<numeric>|MIN|MAX}

VFLuctuation:IEC33:DTIMe?

Parameter Value:

30 to 180 (The default is 60.)

Unit:

Response

Returns the d measurement time in the <NR3> format.

** RST

RST

** RST

RST

** RST

RST

Содержание KHA3000









































































































































































































































































































































































































Результаты поиска

Содержание KHA3000

Отзывы:

Kikusui KHA3000, Руководство по эксплуатации, Страница: 313 / 392

Результаты поиска

Содержание KHA3000

Отзывы: