Kikusui KHA3000 Скачать руководство пользователя страница 309

Страница: 309 / 392

KHA3000

309

Harmonic Measurement Mode (61000-3-12)

Rem

ote Contr

Setting the Rated Value

HARM:IEC312:RAT:DEF

Sets the specification method of the rated current (measured or specified value).

Command

HARMonics:IEC312:RATed:DEFinition {MEASured|SPECified}

HARMonics:IEC312:RATed:DEFinition?

Parameter Value:

MEASured

Measured value (default)

SPECified

Specified value

Response

Returns the specification method of the rated current in the <character> format.

HARM:IEC312:RAT:CURR

Sets the rated current of the EUT.

Command

HARMonics:IEC312:RATed:CURRent <NRf>

HARMonics:IEC312:RATed:CURRent?

Parameter Value:

0.1 to 75.0 (The default is 20.0.)

Unit:

Response

Returns the rated current of the EUT in the <NR3> format.

HARM:IEC312:RAT:VOLT

Sets the rated voltage of the EUT.

Command

HARMonics:IEC312:RATed:VOLTage <NRf>

HARMonics:IEC312:RATed:VOLTage?

Parameter Value:

100 to 600 (The default is 230.)

Unit:

Response

Returns the rated voltage of the EUT in the <NR3> format.

** RST

RST

** RST

RST

** RST

RST

Содержание KHA3000









































































































































































































































































































































































































Результаты поиска

Содержание KHA3000

Отзывы:

Kikusui KHA3000, Руководство по эксплуатации, Страница: 309 / 392

Результаты поиска

Содержание KHA3000

Отзывы: