Kikusui KHA3000 Скачать руководство пользователя страница 308

Страница: 308 / 392

308

KHA3000

Harmonic Measurement Mode (61000-3-12)

Setting the Judgment Rsce

HARM:IEC312:JUDG:RSCE

Sets the judgment Rsce.

Command

HARMonics:IEC312:JUDGe:RSCE{<numeric>|MIN|MAX}

HARMonics:IEC312:JUDGe:RSCE?

Parameter Value:

33 to 350 (The default is 33.)

Response

Returns the judgment Rsce in the <NR1> format.

Setting the Limit Value to be Applied

HARM:IEC312:LVT

Sets the limit value to be applied.

Command

HARMonics:IEC312:LVTable {UNBalanced}|BALanced|SPECified}

HARMonics:IEC312:LVTable?

Parameter Value:

UNBalanced

Except balanced three-phase equipment (default)

BALanced

Balanced three-phase equipment

SPECified

Specified three-phase equipment

Response

Returns the limit value to be applied in the <character> format.

Setting the Nominal System Voltage

HARM:IEC312:NOM:SVOL

Sets the nominal system voltage.

Command

HARMonics:IEC312:NOMinal:SVOLtage <NRf>

HARMonics:IEC312:NOMinal:SVOLtage?

Parameter Value:

100 to 600 (The default is 400.)

Unit:

Response

Returns the nominal system voltage in the <NR3> format.

** RST

RST

** RST

RST

** RST

RST

Содержание KHA3000









































































































































































































































































































































































































Результаты поиска

Содержание KHA3000

Отзывы:

Kikusui KHA3000, Руководство по эксплуатации, Страница: 308 / 392

Результаты поиска

Содержание KHA3000

Отзывы: