Kikusui KHA3000 Скачать руководство пользователя страница 299 | Manualshive

Страница: 299 / 392

Kikusui KHA3000 Скачать руководство пользователя страница 299

13

KHA3000

299

Rem

ote Control

Harmonic Measurement Mode (General)

Setting the Limit Value Standard

HARM:APOW:JIS:CONF

Queries the judgment result when the AC power source was checked and the measured
value was recorded.

Command

HARMonics:APOWer:JIS:CONFirm?

Response

Returns the judgment result in <"string"> format.

PASS: normal, FAIL: abnormal

HARM:APOW:EXEC

Queries whether the measured value was recorded when checking the AC power source.

Command

HARMonics:APOWer:EXECute?

Response

Returns the recording of measured value in <NR1> format.

0: not implemented, 1: implemented or not required

HARM:STAN:LIM

Sets the limit value standard.

Command

HARMonics:STANdard:LIMitation[:NAME] <“string”>

HARMonics:STANdard:LIMitation[:NAME]?

Parameter Value:

“IEC 61000-3-2 Ed3.0”
“IEC 61000-3-2 Ed3.0A2”
“IEC

61000-3-2 Ed2.2

”

“JIS 61000-3-2 2005”
“JIS 61000-3-2 2011”
“JIS 61000-3-2 2019”
“IEC 61000-3-12 2004”
“IEC 61000-3-12 2011”
“IEC 61000-3-2 Ed5.0”

(default)

Response

Returns the limit value standard in the

<“string”>

format.

Use this command when one of the following standards is selected.

•

IEC 61000-3-12 2004

•

IEC 61000-3-12 2011

•

JIS 61000-3-2 2005

(Using reference impedance)

•

JIS 61000-3-2 2019

(Using reference impedance)

** RST

RST

•

The conventional setting value

“

IEC 61000-3-2 Ed3.0A2

”

can be used, but the IEC61000-3-

2 Ed5.0 standard is applied.

•

The conventional setting value

“

JIS 61000-3-2 2011

”

can be used, but the JIS C61000-3-

2(2019) standard is applied.

«
...
297
298
299
300
301
...
»

Содержание KHA3000









































































































































































































































































































































































































Отзывы:

Нет отзывов