Kikusui KHA3000 Скачать руководство пользователя страница 294

Страница: 294 / 392

294

KHA3000

Measurements in General

Setting the Wiring Method of a Measurement Circuit

INP:WIR:METH

Sets the wiring method.

Command

INPut:WIRing:METHod <“1P2W”|“1P3W”|“3P3W”|“3P4W”>

INPut:WIRing:METHod?

Parameter Value:

“1P2W”

Single-phase two-wire

“1P3W”

Single-phase three-wire

“

P3W”

Three-phase three-wire

“

3P4

W”

Three-phase four-wire (default)

Response

Returns the wiring method in the

<“string”>

format.

Setting the Type of Input Coupling

INP:COUP

Sets the type of input coupling. Each input phase (channel) is set to the same value.

Command

INPut:COUPling {AC|DC}

INPut:COUPling?

Parameter Value:

AC coupling

DC coupling (default)

Response

Returns the setting of input coupling in the <character> format.

Setting the Anti-aliasing Filter

INP:FILT:FREQ

Sets the anti-aliasing filter. The cutoff frequency of the filter is set. Each input phase is set to
the same value.

Command

INPut:FILTer:FREQuency {<numeric>|MIN|MAX}

INPut:FILTer:FREQuency?

Parameter Value:

0 (Bypass)
6 000 (default)
15 000

Unit:

** RST

RST

** RST

RST

** RST

RST

Содержание KHA3000









































































































































































































































































































































































































Результаты поиска

Содержание KHA3000

Отзывы:

Kikusui KHA3000, Руководство по эксплуатации, Страница: 294 / 392

Результаты поиска

Содержание KHA3000

Отзывы: