Kikusui KHA3000 Скачать руководство пользователя страница 292

Страница: 292 / 392

292

KHA3000

Measurements in General

Setting the Operation Mode

FUNC

Sets the operation mode.

Command

[SENSe:]FUNCtion[:ON]

“{HARMonics|VFL|OTHer:BASic|OTHer:FFT|OTHer:RUSH}”

[SENSe:]FUNCtion[:ON]?

Parameter Value:

“HARMonic

”

Harmonic measurement mode (default)

“VF

”

Voltage fluctuation measurement mode

“OTHer:BASic”

Basic measurement

“OTHer:FFT”

FFT analyzer

“OTHer:RUSH”

In-rush current measurement

Response

Returns the present operation mode in the <string> format.
Returns OTH when the top page of Other Measurements is displayed.
Returns

“

”

(blank) when the System Setup or External Control page is displayed.

Setting Linked/independent of the Input Circuits

INP:LINK

Sets the input circuit of each input phase (channel) to linked or independent.

Command

INPut:LINKage {ON|OFF|1|0}

INPut:LINKage?

Parameter Value:

ON(1)

linked (default)

OFF(0)

independent

Response

Returns linked or independent in the <NR1> format.

Setting the Current Input Terminals

INP:CURR:TERM

Sets the current input terminals. Each input phase (channel) is set to the same value. This
command is enabled when the input circuit setting is

“

linked

”

(INP:LINK ON).

Command

INPut:CURRent:TERMinal {SHUNt|CLAMp|BNC}

INPut:CURRent:TERMinal?

** RST

RST

** RST

RST

** RST

RST

Содержание KHA3000









































































































































































































































































































































































































Результаты поиска

Содержание KHA3000

Отзывы:

Kikusui KHA3000, Руководство по эксплуатации, Страница: 292 / 392

Результаты поиска

Содержание KHA3000

Отзывы: