manualshive.com logo in svg

Kikusui KHA3000, Руководство по эксплуатации, Страница: 274 / 392

Поделиться
Скачать
Kikusui KHA3000 Скачать руководство пользователя страница 274

274

KHA3000

Storage Media

2

Remove the USB flash drive from the USB connector of this product.

Operation-verified USB flash drive

The USB flash drives listed below have been tested to check that they can save and load test
condition files. The test condition files can be normally loaded and the screen hardcopy can
be normally saved.

Setting the Storage Media

p. 88

The storage media can be set by System Setup Menu (2/3).

Change the storage media from the CompactFlash card to the 

USB flash drive

1

Press the F2 key to select the USB Memory (USB flash drive).

The dialog box displays “Change of the storage media. Please remove the USB memory.”

After the operation, it may take a few seconds till the display of menu buttons switches.

2

Remove the USB flash drive temporarily and then connect it. 

The storage media is set to the USB flash drive. 
Remove the USB flash drive temporarily when the storage media is changed from the
CompactFlash card to the USB flash drive.
If  the  USB  flash  drive  is  not  remove  temporarily  and  then  the  HARD  COPY  key  is
pressed,  t

he  buzzer  sounds  and  the  dialog  box  “Disk  Error.  Media  could  not  be

detected” is displayed.

In  this case,  press  the F1 key  (OK) and remove  the USB  flash drive  temporarily and
then connect it. 

Change the storage media from the USB flash drive to the 

Compact-Flash card

1

Press the F2 key to select the CompactFlash card (CF card).

The dialog box displays “Change of the storage media. Please remove the USB memory.”

The storage media is set to the CompactFlash card.
After the operation, it may take a few seconds till the display of menu buttons switches.

Type

Manufacturer name

Model No.

Capacity

CompactFlash

Buffalo

YUF-4G

 4 GB

Buffalo

YUF-16G

16 GB

Buffalo

RUF2-LV16GS

16 GB

See

Содержание KHA3000









































































































































































































































































































































































































Отзывы:

Нет отзывов