manualshive.com logo in svg

Kikusui KHA3000, Руководство по эксплуатации, Страница: 270 / 392

Поделиться
Скачать
Kikusui KHA3000 Скачать руководство пользователя страница 270

270

KHA3000

Folder and File Configurations

The system is composed of five specific folders. When a file is saved, a date-specific folder is
created in the corresponding specific folder. The date is automatically assigned according to
the date/time setting.

Specific Folders and Date-specific Folders

Specific folder

•

HASET (for saving test conditions for harmonic current tests)

•

HARES (for saving results files and printed reports for harmonic current tests)

•

VFSET (for saving test conditions for voltage fluctuation tests)

•

VFRES (for saving results files and printed reports for voltage fluctuation tests)

•

HARDCOPY (for saving screen hard copies)

Date format of date-specific folder

Specific folder

Date-specific folder

File

HASET

Specific 
to date

HASETnnn.HS

HASETnnn.PDF

HASETnnn.TXT

HARES

Specific 
to date

HARESnnn.HR

HAPDFnnn.PDF

HATXTnnn.TXT

VFSET

Specific 
to date

VFSETnnn.VS

VFSETnnn.PDF

VFSETnnn.TXT

VFRES

Specific 
to date

VFRESnnn.VR

VFPDFnnn.PDF

VFTXTnnn.TXT

HARD
COPY

Specific 
to date

DISPnnn.BMP

Storage Media

Folder type

Date-specific folder

Folder name

yyyymmdd

yyyy indicates the year, mm indicates the month and dd indicates the day 
(automatically assigned).

Содержание KHA3000









































































































































































































































































































































































































Отзывы:

Нет отзывов