Kikusui KHA3000 Скачать руководство пользователя страница 261 | Manualshive

Страница: 261 / 392

Kikusui KHA3000 Скачать руководство пользователя страница 261

11

KHA3000

261

FFT Analyzer

Other Measurements

Voltage Range, Current Range and Wiring Method

The FFT Analyzer Submenu 2/3 is identical to the Basic Measurement Submenu 2/3.

Scaling, Current input Terminal

The FFT Analyzer Submenu 2/3 is identical to the Basic Measurement Submenu 2/3.

LPF and AC Coupling

No.

Menu item

Description

Default

1

LPF

Select the cut-off frequency of the anti-aliasing filter. Select "Bypass" is
no filter is used. If it is the first time to enter the FFT Analyzer submenu,
15 kHz is selected.

15 kHz

2

AC Coupling

Select the input coupling mode for voltage and current measurements.
DC is for DC coupling and AC is for AC coupling. If it is the first time to
enter the FFT Analyzer submenu, DC is selected.

DC

3

Return to Top Menu

Returns to the top menu of Other Measurement.

–

4

Prev/Next

　

Page 3/3

Switches to another sub-menu page.

–

F key: Function key. You can also use the ESC key to return.

3/3

F1

LPF

6 kHz
15 kHz
Bypass

F2

AC Coupling

DC
AC

F5

Return to Top Menu

F6

Prev/Next

Page 3/3

FFT Analyzer Sub-menu

1

3

2

4

«
...
259
260
261
262
263
...
»

Содержание KHA3000









































































































































































































































































































































































































Отзывы:

Нет отзывов