Kikusui KHA3000 Скачать руководство пользователя страница 242 | Manualshive

Страница: 242 / 392

Kikusui KHA3000 Скачать руководство пользователя страница 242

242

KHA3000

View Setting Sub-menu

Flicker List

•

The display color of numeric values changes.

•

Used for observation, analysis and judgment.

●

Explanation of display items

No.

Menu item

Description

Default

1

Scroll

A scroll bar is displayed when there are too many items to be displayed
simultaneously. Use the scroll bar to see the hidden portion of the
screen. Turn the small knob to vertically move the screen.

–

2

Check View Phase

Select a phase to be displayed.

L1

3

Return

Terminates the view setting.

–

F key: Function key. You can also use the ESC key to return.

Measured value Judgment

Red

Part exceeding 100% of the limit value

Yellow

Part exceeding the set margin value and up to 100% of the limit value

Black

Part up to the set margin value

Item

Pst

P0.1

P1s

P3s

P10s

P50s

Description Short-time

flicker value of
one segment
time

Parameters for Pst calculation

Seg 1, 2--- The Pst measurement time corresponds to one segment (Seg1 or any later segment) time.

Plt

Long-time flicker value in all segment (Seg1 and subsequent segments) times (set with the
Pst measurement count).

F1

Scroll

(Input numeric value)

F5

Check View Phase

L1
L2
L3

F6

Return

1

3

2

«
...
240
241
242
243
244
...
»

Содержание KHA3000









































































































































































































































































































































































































Отзывы:

Нет отзывов