manualshive.com logo in svg

Kikusui KHA3000, Руководство по эксплуатации, Страница: 209 / 392

Поделиться
Скачать
Kikusui KHA3000 Скачать руководство пользователя страница 209

9

KHA3000

209

Setting Test Conditions (61000-3-3)

Ex

ecuting V

olta

g

e Fluctuation T

ests

8

Press the F2 key to select Current Range.

Select  the  range  on  the  basis  of  the  maximum  current  obtained  in  step  4.  We
recommend performing the test using a fixed range.
If  you  do  not  know  the current,  select  AUTO  (auto  range).  In  auto  range,  however,  it
takes  approximately  6  seconds  for  the  measured  values  to  stabilize  after  the  range
switches.  If  a  current  variation  causes  the  range  to  switch,  wait  at  least  6  seconds
before starting the test. During the test, the range is fixed to the present range.

9

Press the F6 key to return.

Input Procedure with Specified is Selected in the Setting Menu

Use the following procedure for specifying the nominal voltage.

1

Press the Vf key.

The Vf-Test Conditions List display appears.

2

Press the F6 key to select menu page 1/4.

3

Press the F3 key to select Nominal Values.

A sub-menu is displayed.

4

Press the F1 key to select Specified in Nominal Voltage.

5

Press  the  F2  key  to  input  a  nominal  voltage  value  (Specified  Nominal
Voltage).

The input range is 100 V to 600 V.

6

Press the F6 key to return.

Inputting Comments for Report Printing

1

Press the Vf key.

The Vf-Test Conditions List display appears.

2

Press the F6 key to select menu page 3/4.

3

Press the F3 key to select Comment Input.

A sub-menu is displayed.

4

Input comments for the menu items.

p. 188

The input comments can be checked on the screen.

5

Press the F6 key to return.

See

Содержание KHA3000









































































































































































































































































































































































































Отзывы:

Нет отзывов