Kikusui KHA3000 Скачать руководство пользователя страница 163 | Manualshive

Страница: 163 / 392

Kikusui KHA3000 Скачать руководство пользователя страница 163

7

KHA3000

163

Observation, Analysis and Judgem

ent of Harm

onics

View Setting Sub-menu

The configuration of the View Setting sub-menu is shown below. Observation, analysis and
judgment are executed using 10 types of graphs or numeric value display. The general judg-
ment of conformance to the standards is performed using the test results.

View Setting sub-menu and view area

When the view area is set to 1-Screen, the View Setting sub-menu becomes the sub-menu of
the view selected in View Type. When set to 2-Screen, 3-Screen or 4-Screen, select the view
type using the UP/DOWN and LEFT/RIGHT keys. The sub-menu of the selected view
appears.
Selecting the view type using the UP/DOWN and LEFT/RIGHT keys when the sub-menu is
displayed returns the screen from the sub-menu. Press the F2 key again to display the View
Setting menu.

V/I Waveform

2D Harmonics

3D Harmonics

Meter

Vector

List

Harmonics List

Curr Trend

Harmonics Trend

Result List

Sub-menu of the view type selected in F1

F1

View Type

V/I Waveform
2D Harmonics
3D Harmonics
Meter
Vector
List
Harmonics List
Curr Trend
Harmonics Trend
Result List

F2

View Setting

→

Sub Menu

«
...
161
162
163
164
165
...
»

Содержание KHA3000









































































































































































































































































































































































































Отзывы:

Нет отзывов