KIKKA BOO MULTISTAGE, Инструкция по эксплуатации

Страница: 12 / 70

БЪЛГАРСКИ
ENGLISH
11. FOR INSTALLATION WITH ISOFIX (ISOFIX ATTACHMENTS AND TOP TETHER)
11.1. Fit the ISOFIX attachments guides with the ISOFIX attachments anchor points. The ISOFIX attachments guides can protect the surface of the vehicle seat from being torn. They
can also guide the ISOFIX attachments connectors. (Figure 11.1)
11.2 Extend the ISOFIX attachments connectors by depressing on the release button whilst pulling on the connector.(Figure 11.2)
11.3 Make sure that both ISOFIX attachments connectors are securely attached to their ISOFIX attachments anchor points. The colors of the indicators on both ISOFIX attachments
connectors should be completely green.(Figure 11.3)
11.4 The ISOFIX attachments connectors must be attached and locked onto the ISOFIX attachments anchor points.(Figure 11.4) Check to make sure the child restraint is securely
installed by pulling on the both ISOFIX attachments connectors. Select the desired recline position before moving back against the vehicle seat, as once the top tether is attached and
tensioned, the recline angle will not be able to change without adjustment to the top tether.
11.5. Press the ISOFIX attachments release button and push the child restraint back against the vehicle seat until tight.(Figure 11.5)
11.6 To extend Top Tether for use, press button on Tether Adjuster and pull to lengthen.(Figure 11.6)
11.7 Connect the tether hook securely to the anchorage fitting. (Figure 11.7) USE Top Tether for toddler mode installation if vehicle is equipped with a Tether anchorage fitting and
vehicle requirements are met (see vehicle owner's manual).
11.8. Correctly assembled ISOFIX (ISOFIX attachments and top tether) is shown. Make sure that tether hook are securely attached to the anchorage fitting. The colors of the indicators
on tether strap adjuster should be completely green. (Figure 11.8)
If recline angle is adjusted, check the tension on the top tether, or loosen to adjust angle then re-tension.
12. REMOVE THE ISOFIX.
12.1. Press the secondary lock button first and then the button before pull on the ISOFIX attachments connectors. The ISOFIX
attachments is folded completely.
12.2 .When not in use, Top Tether MUST be properly stored. To make sure the top tether is properly stored away, remove any slack in strap to avoid the top tether swinging around
when the vehicle is in progress.
13. SECURING YOUR CHILD IN THE CHILD RESTRAINT
When installing the child restraint in the toddler mode, do not use the infant insert. While pressing the harness adjustment button, pull completely the two shoulder harnesses of
the child restraint. Press the red button to disengage the buckle. Place the child in the child restraint and engage the buckle. Pull down the adjustment webbing and adjust it to the
proper length so that your child is snugly secured. After the child is seated, recheck whether the shoulder harnesses are at proper height.
Make sure the space between the child and the shoulder harness is about the thickness of one hand.
14. INSTALLING IN GROUP III (Forward Facing Mode / for Child 15–36kg)
Just use the vehicle seat belt when installing the child restraint in the junior mode, do not use the infant insert or 5 point harness, please store the shoulder harnesses, buckle and
buckle tongues in respective storage compartments. Please adjust the shoulder harnesses to proper length before store the shoulder harnesses and buckle in their storage
compartments. Adjust the child restraint to proper angle Angle indication: With top triangle and red triangle aligned. When installing and adjusting the safety belts, make sure that
both the shoulder belt and the waist belt are not twisted and will not keep the safety belts from being properly positioned.
14.1 Press the red button to disengage the buckle. (Figure 14.1)
14.2 Remove the infant insert and crotch pad. (Figure 14.2) When installing the child restraint in the Junior mode, do not use the infant insert.
14.3 Detach the snaps.
14.4 Lift the upper flap upward and pull the lower flap forward, and then store the shoulder harnesses and buckle in their storage compartments. (Figure 14.2)
14.5 Pull the buckle to the back of the seat pad, and then store the buckle and buckle tongues in respective storage compartments.(Figure 14.2)
14.6 Do reattach the snaps to recover the seat pad. The reassembled seat pad is shown.
15. SECURING YOUR CHILD IN THE CHILD RESTRAINT
For installation with 3-point-belt
1. Place the child in the child restraint and check whether the shoulder belt guides are at proper height.
2. Position shoulder belt through shoulder belt guide. Fasten buckle and pull the vehicle belt to tighten.
Shoulder belt must pass through shoulder belt guide. Waist belt must pass through lap belt guidings. The vehicle waist belt must cross through the middle of the crotch belt cover
and then attach the loop and hook fasteners. The child restraint can not be used if the vehicle safety belt buckle is too long to anchor the child restraint securely. Do not use shoulder
belt loose or positioned under arm. Do not use shoulder belt behind child’s back. Do not allow child to slide down in the child restraint in case of strangulation.
16. INSTALLATION WITH 3-POINT-BELT AND ISOFIX ATTACHMENTS
16.1 Installation with ISOFIX attachments is show .
16.2 Place the child in the child restraint and check whether the shoulder belt guides are at proper height.
16.3.Installation with 3-point-belt is show.
16.4 Correctly assembled 3-point-belt and ISOFIX attachments is show. Make sure that both ISOFIX attachments connectors are securely attached to their ISOFIX attach ments anchor
points. The colors of the indicators on both ISOFIX attachments connectors should be completely green. Check to make sure the child restraint is securely installed by pulling on the
both ISOFIX attachments
connectors. Shoulder belt must pass through shoulder belt guide. The vehicle waist belt must cross through the middle of the crotch belt cover and then attach the loop and hook
fasteners. Waist belt must pass through lap belt guidings. The child restraint can not be used if the vehicle safety belt buckle is too long to anchor the child restraint securely. Do not
use shoulder belt loose or positioned under arm. Do not use shoulder belt behind child’s back. Do not allow child to slide down in the child restraint in case of strangulation.
17. CLEANING
Detach Soft Goods 1. Press the red button to disengage the buckle. 2. Remove the infant insert and crotch strap. 3. Detach the elastic on the head support, and then remove the head
support. 4. Detach the snaps o n the seat pad, pull the buckle to the back of seat pad, and then remove the seat pad. To assemble soft goods, reverse the steps above. After removing
the foam of infant insert, please store it somewhere that the child can not access it. Please wash the soft goods with cold water under 30°C. Do not iron the soft goods. Do not bleach
or dry clean the soft goods. Do not use undiluted neutral detergents gasoline or other organic solvent to wash the child restraint. It may cause damage to the child restraint. Do not
twist the soft goods to dry with great force. It may leave the soft goods with wrinkles. Please hang dry the soft goods in the shade. Please remove the child restraint from the vehicle
seat if not in use for a long period of time.