Kidde Alarmline II Скачать руководство пользователя страница 4

 

ii 

Dual Zone Digital Location Control Unit Installation and Operation Manual 

Important information 

Kidde Products Ltd. has taken every care to ensure that Alarmline II Digital 
Linear Heat Detection systems are as simple to install as possible but in case of 
difficulty, please contact our Help Line to ensure trouble free installation and 
operation. 

Kidde Products Ltd. takes no responsibility for damage or injury occasioned as a 
result of failing to install or operate the equipment in accordance with these 
instructions. 

Limitation of liability 

To the maximum extent permitted by applicable law, in no event will UTCFS be 
liable for any lost profits or business opportunities, loss of use, business 
interruption, loss of data, or any other indirect, special, incidental, or 
consequential damages under any theory of liability, whether based in contract, 
tort, negligence, product liability, or otherwise. Because some jurisdictions do not 
allow the exclusion or limitation of liability for consequential or incidental 
damages the preceding limitation may not apply to you. In any event the total 
liability of UTCFS shall not exceed the purchase price of the product. The 
foregoing limitation will apply to the maximum extent permitted by applicable law, 
regardless of whether UTCFS has been advised of the possibility of such 
damages and regardless of whether any remedy fails of its essential purpose. 

Installation in accordance with this manual, applicable codes, and the instructions 
of the authority having jurisdiction is mandatory. 

While every precaution has been taken during the preparation of this manual to 
ensure the accuracy of its contents, UTCFS assumes no responsibility for errors 
or omissions. 

Advisory messages 

Advisory messages alert you to conditions or practices that can cause unwanted 
results. The advisory messages used in this document are shown and described 
below. 

 

WARNING: 

Warning messages advise you of hazards that could result in injury 

or loss of life. They tell you which actions to take or to avoid in order to prevent 
the injury or loss of life. 

 

Caution: 

Caution messages advise you of possible equipment damage. They tell 

you which actions to take or to avoid in order to prevent the damage. 

 

Note: 

Note messages advise you of the possible loss of time or effort. They 

describe how to avoid the loss. Notes are also used to point out important 
information that you should read. 

Содержание Alarmline II






























Отзывы: