August 1999
76-100016-001
Intelligent Suppression Control/Fire Alarm System
PEGAsys
3-9
Figure 3-10. Agent Release Output Module, Details
Module Address
Assignment
Reset Switch
Trouble LED
12
TB1
1
Auxiliary Power
Release Circuits
Signal Circuits
}
See Note 2
Note 1: Only a maximum of 8 of this type module can be used on the system.
Refer to paragraph 1-2.7, in Chapter 1, for other limitations.
2: W1 and W2 must be cut when the auxiliary power input is used.
RELEASE
76-100001-001
3-3.8
Agent Release Output Module
The
PEGAsys
panel has the capacity for a maximum of 8 agent
release output modules, which provides up to 8 possible release
circuits and 24 maximum signal outputs on these modules.
Each Agent Release Output card is equipped with a 24V, su-
pervised output which is programmable for solenoid-type dis-
charge controls. The installer must select discharge control type
required during software configuration programming. The cir-
cuit shall be supervised for open or ground fault conditions. The
ability for individual release output isolate is provided through
the system operator menu.
Each card is equipped with supervised signaling outputs for 3
Style “Y” 24 VDC polarity reversing type indicating circuits. Each
signal circuit is supervised for open, short and ground fault con-
ditions. The ability for individual output isolation is provided
through the system operator menu. Careful consideration of
alarm strobe in-rush currents has been made.
The agent release output circuit is rated for 24 VDC control
devices. Each release output can supervise and activate up to
two (2) solenoid control heads.
Table 3-2 details all devices with which the agent release mod-
ule is approved for operation.
Table 3-2. Approved Release Output Devices
r
e
r
u
t
c
a
f
u
n
a
M
s
d
i
o
n
e
l
o
S
l
a
w
n
e
F
-
e
d
d
i
K
&
0
0
5
6
8
4
1
0
0
0
5
6
8
4
l
a
w
n
e
F
-
e
d
d
i
K
1
8
1
0
9
8
l
a
w
n
e
F
-
e
d
d
i
K
4
9
4
7
9
8
l
a
w
n
e
F
-
e
d
d
i
K
5
7
1
9
9
8
l
a
w
n
e
F
-
e
d
d
i
K
0
3
6
5
9
8
s
r
e
r
u
t
c
a
f
u
n
a
M
s
u
o
i
r
a
V
&
,
E
,
D
,
B
,
A
s
p
u
o
r
G
M
F
G
s
d
i
o
n
e
l
o
S
r
e
l
k
n
i
r
p
S
Power for standby and alarm operation of release and signaling
outputs shall derive from one of two sources; 1) primary supply up
to its capacity, or 2) auxiliary power supply input. Input of auxiliary
power is hardwired through terminals 1 & 2 on the modules termi-
nal block. Output circuits are Listed for use in Power Limited appli-
cations. All signaling power is fully regulated.
Содержание PEGAsys
