![background image](http://html.mh-extra.com/html/kidde-fire-systems/ecs/ecs_manual_1965380096.webp)
Design and Installation
06-236115-001
4-33
October 2014
4-3.14
Installation of Cable Operated Control Head, P/N 81-979469-000
The following procedures must be performed before attaching the control head to the cylinder
valve.
1. Remove the protection cap from the cylinder actuation port.
2. Remove the cover from the control head and take out the wheel assembly, cable pipe lock-
nut and closure disc.
3. Make sure the plunger is below the surface of the control head body. Position the control
head at the valve control port with the arrow pointing in the direction of pull.
4. Assemble the cable pipe locknut to the cable pipe and place the cable pipe in the control
head body.
5. Slide the wheel assembly on the control cable to the SET position. Tighten the set screws
securely. Make sure the wheel assembly is at the start of the stroke.
6. Cut off any excess control cable close to the wheel assembly.
7. Insert the closure disc and replace the cover on the control head. The control head is now
armed.
8. Assemble control head to cylinder valve actuation port. Tighten swivel nut securely.
4-3.15
Installation of Lever Operated Control Head, P/N WK-870652-000
1. Ensure the control head is in the SET position with the safety pull pin and seal wire intact.
2. Remove the protection cap from the cylinder valve actuation port.
3. Using a suitable wrench, assemble the control head to the cylinder valve actuation port.
Tighten the swivel nut securely.
WARNING
The cable operated control head (P/N 81-979469-000) must not be used with
the stackable pressure operated control head (P/N 82-878750-000). Installing
the cable operated control head on the actuation port of the stackable pressure
operated control head will cause the device to malfunction.
CAUTION
To ensure the manual lever does not snag or trap the cable, make sure the local
manual release lever is in the SET position with the locking pin and seal wire
installed before assembling the control head cover to the body.
Содержание ECS
