IS-10797-US
We’re here to help
866-558-5706
Hrs: M-F 9am to 5pm EST
REV 04-JUNE-2021
For warranty information please visit: kichler.com/warranty
1) Screw end of threaded pipe into hole in center of
mounting strap so approximately 1/4” of thread is
exposed on the extruded side of mounting strap.
2)
Thread hexnut onto the shorter end of the threaded
pipe. Tighten to secure.
3)
Connect the mounting strap to the outlet box with the
strap mounting screws.
4) Grounding instructions: (See Illus. A or B)
a)
On fixtures where mounting strap is provided with a
hole and two raised dimples, wrap ground wire from
outlet box around green ground screw, and thread
into hole.
b) On fixtures where a cupped washer is provided, put
ground wire from outlet box under cupped washer
and green ground screw and thread screw into hole
in mounting strap.
If fixture is provided with ground wire, connect fixture
ground wire to outlet box ground wire with wire
connector after following the above steps. Never connect
ground wire to black or white power supply wires.
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
Fixture Diagram
Cautions
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starting and during the installation.
WARNING:
This fixture is intended for installation in accordance with the
National Electrical Code (NEC) and all local code specifications.
If you are not familiar with code requirements, installation by a
certified electrician is recommended.
DIMMING:
This LED fixture is compatible with most standard incandescent
dimmers, LED dimmers, and electronic low voltage dimmers.
For optimal performance, an electronic low voltage dimmer should
be used.
See kichler.com/dimming for a list of compatible dimmers.
CLEANING:
• Always be certain that electric current is turned off before
cleaning.
• Only a soft damp cloth should be used. Harsh cleaning
products may damage the finish.
Installation Instructions
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including
interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Information:
Installation Instructions (continued)
5) Make wire connections. Reference chart below for
correct connections and wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black
White
*Parallel cord
(round & smooth)
*Parallel cord
(square & ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth (See illus.)
Neutral Wire
6)
Carefully push wire connections back into outlet box
making sure all connections remain secure.
7)
Push fixture to wall, pass the center hole of the fixture
over the threaded pipe on the mounting strap.
8)
Slip the spacer onto the threaded pipe and into the
center of the module hole.
9)
Slip lockwasher over threaded pipe. Thread hexnut onto
the threaded pipe. Tighten to secure.
10)
Carefully lower each diffuser and rest onto the bottom
tabs of the side brackets.
STRAP MOUNTING SCREW(S)
THREADED PIPE
MOUNTING STRAP
WIRE
CONNECTORS
OUTLET BOX
SPACER
HEXNUT
DIFFUSER
LED MODULE
COVER
SIDE BRACKET
HEXNUT
