KI ROGUE 2 Скачать руководство пользователя | Manualshive

Страница: 51 / 58

background image

50

Wheelbase Width Adjustment

Adjusting the wheelbase width allows the rider the option to move the wheels closer or further away from
the hips. It also compensates for camber adjustment and gives the proper wheel spacing to maximize
pushing efficiency.

To Adjust the Wheelbase Width

1. Remove the lower base mounts (B) by removing two bolts (A) per side using a 3mm Allen wrench. If

anti-tips are present, the image will look different, but the process is the same.

2.   Move the dimple clip (C) to the dimple on the camber plug (D) that provides the desired spacing.
3.   Repeat on opposite side.
4.   When both sides are spaced equally, tighten the bolts (A) to 70 in/lbs.

A

B

C

D

«
...
49
50
51
52
53
...
»

Содержание ROGUE 2



























































Отзывы:

Нет отзывов

Похожие инструкции для ROGUE 2

Бренд: Invacare Страницы: 12

Бренд: Karma Страницы: 64

Бренд: RHealthCare Страницы: 41

Бренд: Vela Страницы: 20

Power Chairs 600

Бренд: Quantum Rehab Страницы: 2

Бренд: Küschall Страницы: 40

Бренд: rainbow care Страницы: 4

Бренд: Quickie Страницы: 92

Бренд: Mobiclinic Страницы: 7

Бренд: Sopur Страницы: 26

Бренд: Sopur Страницы: 88

Бренд: Special mobility Страницы: 30

Бренд: Sunrise Страницы: 2

JAY ConfigureFit

Бренд: Sunrise Страницы: 20

Бренд: Sunrise Страницы: 24

Бренд: Kohler Страницы: 3

Sterling 72186104

Бренд: Kohler Страницы: 12

Бренд: DDO Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды