Keysight U8001A Скачать руководство пользователя

Страница: 56 / 81

Service Guide

Keysight U8001A/U8002A User’s and Service Guide

Self-Test Procedures

Power-on self-test

Each time the power supply is powered on, a set of self-tests are performed.

These tests check that the minimum set of logic and measurement hardware are

functioning properly.

Unit fails self-test

Verify that the correct power-line voltage setting is selected. Also, ensure that all

terminal connections are removed while the self-test is performed. Please refer to

Appendix A: List of Error Codes

for list of error codes.

Line Voltage Fuse Rating

indicator for U8001A

Line Voltage Fuse Rating

indicator for U8002A

NOTE

The authorised personnel will mark the fuse rating indicator printed on the rear

panel each time the fuse is changed.

Содержание U8001A


















































































Результаты поиска

Содержание U8001A

Отзывы:

Похожие инструкции для U8001A

Бренды по названию

Популярные бренды

Keysight U8001A, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание U8001A

Отзывы:

Похожие инструкции для U8001A

Бренды по названию

Популярные бренды