Keysight U8001A Скачать руководство пользователя

Страница: 45 / 81

Operations and Features

Keysight U8001A/U8002A User’s and Service Guide

System Related Operations

Reset to factory defaults

To reset the power supply unit to factory defaults, press and hold “Output On/Off”

button when power-up.
– The OVP and OCP are turned off and their values are set to maximum.
– The memory storage locations are cleared

– The voltage and current limit values are set to zero.
– The calibration values are intact.

Power-on self-test

A power-on self-test occurs automatically when the power supply unit is turned

on. This test ensures the unit is operational. The power-on self-test checks for

flash data memory and checks the voltage and current outputs when the unit is

off.

NOTE

If the test fails, the display will show “Err” with the error code. See

Appendix A:

List of Error Codes

for more information.

Содержание U8001A


















































































Результаты поиска

Содержание U8001A

Отзывы:

Похожие инструкции для U8001A

Бренды по названию

Популярные бренды

Keysight U8001A, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание U8001A

Отзывы:

Похожие инструкции для U8001A

Бренды по названию

Популярные бренды