Keysight U8001A Скачать руководство пользователя

Страница: 3 / 81

Keysight U8001A/U8002A User’s and Service Guide

Safety Symbols

The following symbols on the instrument and in the documentation indicate

precautions that must be taken to maintain safe operation of the instrument.

Direct current

Off (supply)

Alternating current

On (supply)

Both direct and alternating current

Equipment protected throughout by

double insulation or reinforced

insulation.

Three-phase alternating current

Caution, risk of electric shock.

Earth (ground) terminal

Caution, risk of danger (refer to this

manual for specific Warning or Caution

information.

Protective conductor terminal

Caution, hot surface.

Frame or chassis terminal

Out position of a bi-stable push

control.

Equipotentiality

In position of a bi-stable push control.

Содержание U8001A


















































































Результаты поиска

Содержание U8001A

Отзывы:

Похожие инструкции для U8001A

Бренды по названию

Популярные бренды

Keysight U8001A, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание U8001A

Отзывы:

Похожие инструкции для U8001A

Бренды по названию

Популярные бренды