Keysight U1401B Скачать руководство пользователя страница 23

Страница: 23 / 159

Getting Started

Keysight U1401B User’s and Service Guide

Product Overview

Slide switch

The slide switch has the following positions:
–

Charge

: Select this position to charge the batteries. Use the AC adapter

provided to charge this instrument.

–

: Select this position to enable only the measurement functions.

–

M/S

: Select this position to enable both the measurement and source

functions.

Figure 1-1

The slide switch

Table 1-2

Slide switch functions

No.

Description

Function

External AC adapter jack

Allows an external AC adapter to be connected to provide power or charge the batteries.

CHARGE

Charges the batteries with an external AC adapter.

Enables only the measurement functions.

M/S

Enables both measurement and source functions.

Slide Switch

—

Charging indication

Indicates the charging process.
GREEN: Fully charged
YELLOW: Charging

Содержание U1401B
































































































































































Результаты поиска

Содержание U1401B

Отзывы:

Похожие инструкции для U1401B

Бренды по названию

Популярные бренды

Keysight U1401B, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание U1401B

Отзывы:

Похожие инструкции для U1401B

Бренды по названию

Популярные бренды