Keysight N9923A Скачать руководство пользователя страница 95

Страница: 95 / 276

Keysight N9923-90001 User’s Guide

DTF (Distance to Fault) Measurements
DTF Measurement Settings

— Press

Meas Setup 4

— Then

DTF Cable Specifications

— Select

Cable Corr

—

Auto

Use Cable Loss and Velocity Factor values from a Cable file. See

“How to Edit, Save, and Recall a Cable File” below. This will overwrite
a manually-entered value.

—

Man

(Default setting) Manually enter a value for Cable Loss and

Velocity Factor.

— Then:

—

Velocity Factor

Using the numeric keypad, enter a value between 0.01

and 1. Then press

Enter

—

Cable Loss

Using the numeric keypad, enter a positive Cable Loss

value in dB/m, then press

Enter

How to Edit a Cable File

The FieldFox includes many predefined cable files with the manufacturer’s
specifications. You can edit these files or create new cable files using the
following procedure or using the FieldFox Data Link Software.

The Cable correction data survives a Mode Preset and Preset.

With a DTF measurement present:

— Press

Meas Setup 4

— Then

DTF Cable Specifications

— Then

Edit/Save/Recall Cables

— Press

New Cable

then

Yes

to clear all data from the existing DTF Cable

table and reset header information to default settings.

— Then

Edit Cable

to open the Cable Editor.

— Then use the

arrows to select a field,

—When editing Cable Description information, press

Edit

then modify

the selected field using the FieldFox labeler.

—When editing Frequency/Loss pairs, enter numbers using the numeric

keypad, then select a frequency suffix. Then

Enter

. Learn more about

“How the Freq/Loss pairs are applied” below.

— Optionally choose from the following:

—

Previous / Next Page

Quickly scrolls through pages of Freq/Loss data.

—

Add Data

Add a blank Freq/Loss pair to the table,

—

Delete/Clear

then:

Содержание N9923A





















































































































































































































































































Результаты поиска

Содержание N9923A

Отзывы:

Keysight N9923A, Руководство пользователя, Страница: 95 / 276

Результаты поиска

Содержание N9923A

Отзывы: