Keysight N9923A Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 276

Keysight N9923A Скачать руководство пользователя страница 85

Keysight N9923-90001 User’s Guide

85

CAT (Cable and Antenna Test) Mode
CAT Mode Settings

Interference Rejection

Use this setting when you suspect that other signals in the area are interfering
with a measurement. Interference may look like a spike or lack of stability in the
measurement trace. While monitoring a measurement at a specific frequency,

toggle this setting between ON and OFF. If the measurement result decreases
while ON, then there is an interfering signal in the area. Continue to make
measurements with Interference Rejection ON. However, this will slow the

measurement speed.

Once enabled, up to SIX sweeps may be required before the interfering signal

is neutralized.

This setting can be changed at any time without affecting calibration accuracy.

How to set Interference Rejection

— Press

Meas Setup 4

.

— Then

Interference Rejection [current setting]

.

— Then choose from the following:

—

Off

No interference rejection and fastest possible sweep speed

—

Minimum

The lowest level of Interference rejection.

—

Medium

The medium level of Interference rejection.

—

Maximum

The highest level of Interference rejection.

«
...
83
84
85
86
87
...
»

Содержание N9923A





















































































































































































































































































Отзывы:

Нет отзывов