Keysight N9923A Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 276

Keysight N9923A Скачать руководство пользователя страница 77

Keysight N9923-90001 User’s Guide

77

CAT (Cable and Antenna Test) Mode
CAT Mode Settings

CAT Mode Settings

Select

CAT Mode

before making any setting in this chapter.

How to select CAT Mode

— Press

Mode

.

— Then

CAT/TDR

.

Measurement Selection

How to select a CAT Mode Measurement

Learn more about the following measurements in the Supplemental Online
Help:

http://na.support.keysight.com/fieldfox/help/SupHelp/FieldFox.htm

Press

Measure 1

.

Then choose one of the following: These softkeys also appear after CAT Mode
is selected.

—

Distance To Fault

1-port reflection measurement that uses Inverse Fourier

Transform (IFT) calculations to determine and display the distance to, and
relative size of, a fault or disruption in the transmission line. Units are in

return loss format, expressed as a positive number in dB, unless the
measurement selected is DTF (VSWR). To learn more about DTF
measurements, refer to

Chapter 6, “DTF (Distance to Fault)

Measurements”, on page 89

.

—

Return Loss & DTF

Displays both a Return Loss measurement and a DTF

measurement. Use this format to display the frequency settings that are
used to make the DTF measurement. The frequency range settings for these
two measurements can be coupled or uncoupled. Learn more on

.

Calibrations are applied to both traces

When in Hold mode and Single sweep is performed, only the active trace

is triggered. Use the

arrows to activate a trace

—

Return Loss

1-port reflection measurement that displays the amount of

incident signal energy MINUS the amount of energy that is reflected. The

higher the trace is on the screen, the more energy being reflected back to
the FieldFox. Learn how to measure Return Loss on

.

—

VSWR

(Voltage Standing Wave Ratio – also known as SWR) 1-port

reflection measurement that displays the ratio of the maximum reflected
voltage over the minimum reflected voltage. The higher the trace is on the

screen, the more energy being reflected back to the FieldFox.

—

DTF (VSWR)

Distance to Fault in VSWR format.

«
...
75
76
77
78
79
...
»

Содержание N9923A





















































































































































































































































































Отзывы:

Нет отзывов