Keysight N9923A Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 276

Keysight N9923A Скачать руководство пользователя страница 50

50 Keysight N9923-90001 User’s Guide

NA (Network Analyzer) Mode
NA Mode Settings

— Enter a time value using the numeric keypad, the

arrows, or the rotary

knob.

— Press a multiplier key. Learn about multiplier abbreviations in

Abbreviations” on page 34

.

Electrical Delay can also be set using the

Mkr->Delay

feature. Learn how on

“Marker Functions” on page 183

Phase Offset

Phase offset mathematically adjusts the phase measurement by a specified
amount, up to 360°. Use this feature in the following ways:

Improve the display of a phase measurement.

This is similar to the way you

would change the reference level in an amplitude measurement. Change the
phase response to center or align the response on the screen.

Emulate a projected phase shift in your measurement.

For example, if you

know that you need to add a cable and that the length of that cable will add a

certain phase shift to your measurement, you can use phase offset to add that
amount and simulate the complete device measurement.

You can set the phase offset independently for each measurement trace.

How to set Phase Offset

— Press

Scale / Amptd

— Then

More

— Then

Phase Offset

— Enter a value in degrees using the numeric keypad, the

arrows, or the

rotary knob. Press

Enter

Averaging

Averaging helps to reduce the effects of random noise on a measurement. You
specify the number of measurements to be averaged. The more measurements

averaged, the greater the amount of noise reduction. An average counter is
shown in the left edge of the screen as

Avg <n>

where <n> is the number of

measurements that are averaged.

Averaging can be set before or after calibration. When set before calibration,
each calibration standard is measured <n> times and averaged. More time is

needed to perform the calibration, but there will be less noise in the resulting
error terms which means that subsequent measurements will also have less
noise. In addition, noise is further reduced by continuing to average after

calibration.

How to set Averaging

— Press

BW 2

.

«
...
48
49
50
51
52
...
»

Содержание N9923A





















































































































































































































































































Отзывы:

Нет отзывов