Keysight N9923A Скачать руководство пользователя страница 48

Страница: 48 / 276

48 Keysight N9923-90001 User’s Guide

NA (Network Analyzer) Mode
NA Mode Settings

— Follow each by entering a value using the numeric keypad, the

arrows,

or the rotary knob.

— After using the

arrows or the rotary knob, press

Enter

. The increment

setting of the arrows is based on the current span and can NOT be changed
in NA Mode.

— After using the keypad, select a multiplier key. Learn more in

“Multiplier

Abbreviations” on page 34

Scale Settings

Adjust the Y-axis scale to see the relevant portions of the data trace. The Y-axis
is divided into 10 graticules.

This setting can be changed at any time without affecting calibration accuracy.

How to set Scale

— Press

Scale / Amptd

— Then choose from the following method

—

Autoscale

Automatically adjusts the Y-axis to comfortably fit the Min

and Max amplitude of the trace on the screen.

—

Autoscale All

Autoscales all of the traces on the screen, useful only for

multi-trace configurations.

—3.Set Scale, Reference Level, and Reference Position

——

Scale

Manually enter a scale per division to view specific areas

of the trace.

——

Ref Level

Manually set the value of the reference line. Enter a

negative value by pressing

Run/Hold (+/-)

either before or

after typing a value.

——

Ref Position

Manually set the position of the reference line.

Values must be between 0 (TOP line) and 10 (BOTTOM line)

Scale annotation on the FieldFox screen

—

Reference Line = red arrow

—

Ref Level = –40 dB

—

Ref Position = 1

—

Scale = 2 dB per division

Содержание N9923A





















































































































































































































































































Результаты поиска

Содержание N9923A

Отзывы:

Keysight N9923A, Руководство пользователя, Страница: 48 / 276

Результаты поиска

Содержание N9923A

Отзывы: