Keysight N9923A Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 276

Keysight N9923A Скачать руководство пользователя страница 45

Keysight N9923-90001 User’s Guide

45

NA (Network Analyzer) Mode
NA Mode Settings

Quick Settings

Both CAT and NA Modes allow you to view and change most relevant settings
from a single location. All of these settings are discussed in this chapter and,
unless otherwise noted, ALL of these settings can also be made using the

standard softkey menus. In the graphic below, the resolution is being edited.

How to view and change Quick Settings

— Press

Meas Setup 4

— Then

Settings

.

— Press

Next Page

and

Previous Page

to view all settings. If these softkeys

are NOT available, then all available settings fit on one page.

— To change a setting:

—Use the

arrows to highlight a setting.

—Then press

Edit

. The current setting changes to

yellow

.

—Some settings require you to press a softkey to change the value.

Otherwise, use the numeric keypad,

arrows, or rotary knob to

change the value.

—When finished changing a value, press

Done Edit

.

— Press

Dock Window

to relocate the Settings table to a position relative to

the trace window. The Dock Window setting persists through a Preset.
Choose from the following:

Interference Rejection and System Z0 can be changed ONLY from the

Quick Settings menu. Learn more about these settings in

Impedance (Z0)” on page 54

.

ALL other settings can also be made using

the standard softkey menus.

«
...
43
44
45
46
47
...
»

Содержание N9923A





















































































































































































































































































Отзывы:

Нет отзывов