Keysight N9923A Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 276

Keysight N9923A Скачать руководство пользователя страница 40

40 Keysight N9923-90001 User’s Guide

NA (Network Analyzer) Mode
NA Mode Settings

S21 and S12 transmission measurements are used to measure the loss or gain
through a DUT over a specified frequency range. Both ends of the DUT must be

connected to the FieldFox. The FieldFox signal source is transmitted out one of
the test port connectors, through the DUT, and into the other test port
connector

How to measure S-parameters

1.

Press

Preset

then

Preset

2.

Press

Measure 1

then choose from the following:

—

S11

Reflection measurement at port 1.

—

S21

Forward 2-port transmission measurement.

—

S12

Reverse 2-port transmission measurement. May require an

option.

—

S22

Reflection measurement at port 2. May require an option.

OR

select a multi-trace configuration. Learn more on

Configurations” on page 43

.

3.

Press

Freq/Dist

then either

Start

and

Stop

or

Center

and

Span

to enter a

Frequency Range for the measurement.

4.

Press

BW 2

then

IFBW

to select the IF Bandwidth for the measurement.

Narrower bandwidths require more time to sweep, but lowers trace noise.

5.

Press

Sweep 3

then

Resolution

to select the number of data points for the

measurement. More data points require more time to sweep.

6.

Press

Cal 5

to calibrate the measurement. Learn more in

“How to Perform

a Calibration” on page 104

.

7.

All other settings can be made AFTER calibration without compromising

measurement accuracy.

Mixed-Mode S-Parameters

In NA Mode ONLY, mixed-mode S-parameters (also known as Balanced
measurements) are available with Option 212.

Because the FieldFox has only two test ports, only reflection measurements are
available. Connect the balanced input or output of your DUT to the FieldFox

ports 1 and 2

For highest accuracy, a Full 2-port calibration is required.

«
...
38
39
40
41
42
...
»

Содержание N9923A





















































































































































































































































































Отзывы:

Нет отзывов