manualshive.com logo in svg

Keysight N9923A, Руководство пользователя, Страница: 256 / 276

Поделиться
Скачать
Keysight N9923A Скачать руководство пользователя страница 256

 256                                                                                                                     Keysight N9923-90001 User’s Guide

Safety Considerations
FieldFox Markings

FieldFox Markings

The CSA mark is a registered trademark of CSA International. 

The RCM Mark is a registered trademark of the Australian Communications and 

Media Authority.

This symbol combines the following three markings:
CE indicates product compliance with all relevant European legal Directives (if 

accompanied by a year, it signifies when the design was proven).
ICES indicates product compliance with the Canadian Interference-Causing 

Equipment Standard (ICES–001).
ISM indicates this is an Industrial Scientific and Medical Group 1 Class B product 

(CISPR 11, Clause 4)

The Standby symbol is used to mark a position of the instrument power line 

switch.

This symbol indicates separate collection for electrical and electronic equipment, 

mandated under EU law as of August 13, 2005. All electric and electronic 

equipment are required to be separated from normal waste for disposal 

(Reference WEEE Directive, 2002/96/EC).

Indicates the time period which no hazardous or toxic substance elements are 

expected to leak or deteriorate during normal use. Forty years is the expected 

useful life of the product.
This symbol indicates the Environmental Protection Use Period (EPUP) for the 

product’s toxic substances and for the China RoHS requirements.

CAUTION, risk of danger, refer to safety information in manual.

Dispose of properly

Hot surface - connectors get hot during extended operation, so care must be 

taken when making connections and disconnections.

Содержание N9923A





















































































































































































































































































Отзывы:

Нет отзывов