Keysight N9923A Скачать руководство пользователя страница 240

Страница: 240 / 276

240 Keysight N9923-90001 User’s Guide

Working with the Lithium-Ion Battery
Viewing the Battery Charge Status

Service Diagnostics—Battery Screen

The Battery screen displays the following information. To access the screen,
select

System

then

Service Diagnostics

then

Battery

Additional battery information is available using SCPI commands.

1. Status

– Fully charged, No battery, Charging, Empty, or Discharging.

2. External DC Supply

– ON or OFF indicates if an external DC supply is

connected.

3. Battery Present

– ON or OFF indicates if a battery is installed.

1. Voltage

– measured by the battery’s sensor.

2. Current

– amount of current being consumed when operating from

internal battery. If battery is charging, indicates amount of charging

current.

3. Battery Temperature

– internal temperature of the battery as measured by

a sensor embedded in the battery.

4. Present Run Time to Empty

– minutes of power remaining based on

amount of current being used now.

5. Charge Cycles

– number of charge cycles the battery has experienced.

Charge cycle defined as

≥

80% change in relative state of charge.

Built-In Battery Gauge

Each lithium ion battery has an LED gauge that displays its charge status. The

gauge is active unless the battery is in shut down mode.

To view the LED gauge, open the FieldFox battery compartment door, remove

the battery, then press the button on the battery.

Battery not charging with 84% battery life

remaining.

Battery fully charged. A fully charged battery

MAY NOT read 100%. Learn more in

“Reconditioning Battery” on page 244

Table 16-1

Front Panel Icons

Icon

Status

Items 4 through 8 are read directly from the battery. The information is

based on the battery’s internal sensors and memory.

Содержание N9923A





















































































































































































































































































Результаты поиска

Содержание N9923A

Отзывы:

Keysight N9923A, Руководство пользователя, Страница: 240 / 276

Результаты поиска

Содержание N9923A

Отзывы: