Keysight N9923A Скачать руководство пользователя страница 23

Страница: 23 / 276

Keysight N9923-90001 User’s Guide 23

Preparing for Initial Use of Your New FieldFox
FieldFox ON/OFF Settings

— On the battery. Open the FieldFox battery compartment door to view the

battery LCD.

To conserve battery power:

— Use

Run/Hold

to single-trigger a measurement when needed.

Hold

shown on the display.

— Press

System

then

Display

then

Brightness

. Use the

arrows, the

rotary knob, or numeric keypad to adjust the brightness to dim the FieldFox
display as much as possible.

— Briefly press the power button to switch to Standby mode when the

FieldFox is not being used. Briefly press the power button to switch to
Standby mode when the FieldFox is not being used. Press again to restore

power. All current settings are preserved.ress again to restore power. All
current settings are preserved.

To recharge a battery:

Use ONLY a FieldFox charger to recharge a battery.

— The battery can be fully charged while in the FieldFox in about 4 hours with

the FieldFox either ON or OFF.

— The battery can be fully charged externally using the external battery

charger in about 4 hours.

When the battery is removed, the FieldFox can still be powered by the AC/DC

adapter.

FieldFox ON/OFF Settings

— To turn power

, briefly press the power button. Boot-up takes about 1

minute.

— To switch to

Standby

mode (low battery drain), briefly press the power

button. See the Note above concerning Stand By.

When powered by the battery only, the FieldFox can stay in Standby mode

for a maximum of four hours and then it powers off automatically. When

the relative battery charge drops by about 20%, the FieldFox will power off

to preserve the remaining charge.

The FieldFox power button shut down/standby sequence includes a 10

second counter that allows you to either choose a softkey to immediately

initiate the action

(

Standby

Shut down

Restart*)

or to let the

countdown counter expire after 10 seconds then perform the action.
*Restart can only be enabled via the

Restart

softkey

Содержание N9923A





















































































































































































































































































Результаты поиска

Содержание N9923A

Отзывы:

Keysight N9923A, Руководство пользователя, Страница: 23 / 276

Результаты поиска

Содержание N9923A

Отзывы: