Keysight N9923A Скачать руководство пользователя страница 215

Страница: 215 / 276

Keysight N9923-90001 User’s Guide

215

System Settings
Preferences

How to save current settings as Preferences

— Using softkeys, configure the settings as you would like them to remain.

— Press

System 7

— Then

Preferences

— Then

Save Current Settings

There is a beep when your settings have been

saved.

— Press

Reset Preferences

to restore the factory default settings.

Global Settings (Overview)

Choose the Global Settings values (Language, Batter Saver, and Startup
Mode). See also

“Quick Settings Table” on page 213

How to select Global Settings:

— Press

System 7

— Then

Preferences

— Then

Preferences

— Then use arrow softkeys or the knob to select Global Settings

— Then

Edit

for each of the following:

—Language (see)

—Batter Save Mode (see)

——On

——Off (default)

—Startup Mode (see)

— Then

Done Edit

(for each change in setting)

Language

Choose the language in which to display FieldFox softkeys and other
messages. Select Save Current Settings to set this language as a preference.

How to select a Language

— Press

System 7

— Then

Preferences

— Then

Language

— Then choose from the following:

—

English

Содержание N9923A





















































































































































































































































































Результаты поиска

Содержание N9923A

Отзывы:

Keysight N9923A, Руководство пользователя, Страница: 215 / 276

Результаты поиска

Содержание N9923A

Отзывы: