Keysight N9923A Скачать руководство пользователя страница 209

Страница: 209 / 276

Keysight N9923-90001 User’s Guide

209

System Settings
Preset

Preset

The Preset key restores the FieldFox measurement settings to a known

condition. You can preset the entire instrument, or just the current Mode (CAT,
NA, and Power Meter).

When Preset, the FieldFox CalReady calibration is recalled for use in CAT and
NA Modes. Learn more in

“CalReady” on page 104

In addition to all

Preference

settings, the following settings always survive

Preset and Mode Preset:

— External Reference state (see

“Frequency Reference Source” on page 226

)

— VVM Display Resolution (see

“Display Resolution” on page 164

)

— Marker Peak Excursion and Threshold (see

“What Is a ‘Peak’” on page 182

)

How to Preset the FieldFox

— Press

Preset

— Then choose one of the following:

—

Preset

Returns ALL Modes to the factory default settings.

—

Mode Preset

Returns only the current Mode to the factory default

settings. The current settings for all other Modes remain.

User Preset

User Preset allows you to store custom settings for each mode, then recall the

settings when the Preset key is pressed. Your custom settings are saved to a
standard State file (UserPreset.sta). However, unlike State files, calibration
data is NOT saved. Learn more about State files in

“Saving and Recalling Files”

on page 192

How to set User Preset

— Make your custom settings for all modes.

— When finished, press

Preset

— Then

Save User Preset,

then select

Yes

to confirm.

— Then

User Preset ON

How to recall User Preset

— Press

Preset

— Then choose from the following:

Содержание N9923A





















































































































































































































































































Результаты поиска

Содержание N9923A

Отзывы:

Keysight N9923A, Руководство пользователя, Страница: 209 / 276

Результаты поиска

Содержание N9923A

Отзывы: