manualshive.com logo in svg

Keysight N9923A, Руководство пользователя, Страница: 178 / 276

Поделиться
Скачать
Keysight N9923A Скачать руководство пользователя страница 178

 178                                                                                                                     Keysight N9923-90001 User’s Guide

Data Analysis Features
All about Markers

How to move a marker between data and memory traces

— Create a data and memory trace that will host the marker. Learn how in 

“How to display data and memory traces” on page 189

.

— Press 

Marker

 and 

Enter

 to create a marker.

— Then 

More

.

— Then select the marker to move using 

Marker 1,2,3,4,5,6

.

— Then toggle 

Marker Trace Auto Data Mem

.

—

Auto

 - Marker resides on data trace when it is visible. Marker resides 

on memory trace when only IT is visible (Default setting).

—

Data

 - Marker resides on data trace, even when not visible. 

—

Mem

 - Marker resides on memory trace, even when not visible. 

Marker Format

The Marker Format setting, available ONLY in NA Mode, allows you to choose 
the format of the marker readout that appears in the upper-right corner of the 

screen and in the marker table. The marker format can be independent of the 
trace format, and can be set independently for each trace. All markers on a 
trace have the same marker format.

How to choose marker format

— Press 

Marker

— Then 

More

— Then 

Marker Format

 

— Then choose from the following:

Selection

Example Y-axis value

Default

 Same as displayed format

R + jX

 Complex impedance format

 

(3rd number is distance for Time Domain)

22.8

Ω

 -j61.4

Ω

 

          287.9fF 

    

Z Magnitude

 Impedance Mag.

66.08

Ω

Phase

73.8°

 

Real

0.2003

More

Imaginary

-0.6727

Mag & Phase

0.705, -73.7°

Содержание N9923A





















































































































































































































































































Отзывы:

Нет отзывов