manualshive.com logo in svg

Keysight N9923A, Руководство пользователя, Страница: 177 / 276

Поделиться
Скачать
Keysight N9923A Скачать руководство пользователя страница 177

Keysight N9923-90001 User’s Guide

                                                                                                                      177

Data Analysis Features
All about Markers

Figure 12-3 Coupled Markers move on ALL traces at the same time.

How to create Uncoupled Markers

To create markers that are NOT coupled (move independently on each trace): 

— Press 

Marker

 

— Then 

More

 

— Then 

Coupled Markers OFF 

Marker Colors

As shown in the above image, in NA and CAT Modes, markers are the same 
color as the trace to which they are assigned. I

Marker colors can NOT be changed. 

Marker Trace

Both CAT and NA Modes can display a data trace and a memory trace. By 
default, markers are assigned to the data trace. However, you can move a 
marker between the data and memory trace. The marker moves to the same 

X-axis location on the specified trace. 

When Coupled Markers is ON, this setting applies to the active marker for ALL 

traces that are coupled. Otherwise, this setting applies to the active marker on 
only the active trace.

Markers are coupled by default.

Содержание N9923A





















































































































































































































































































Отзывы:

Нет отзывов