Keysight N9923A Скачать руководство пользователя страница 166 | Manualshive

Страница: 166 / 276

Keysight N9923A Скачать руководство пользователя страница 166

166 Keysight N9923-90001 User’s Guide

VVM (Vector Voltmeter) Mode - Option 308
VVM Mode Settings

— Then

More

— Then

Output Power

—

High

(Default setting) Sets output power to the maximum achievable

power at all displayed frequency. Please see the FieldFox
Specifications for expected power levels

—

Low

Sets output power to approximately –42 dBm.

—

Man

Set output power to an arbitrary value.

— Then press

Nominal Power

— Then enter a value using the numeric keypad, the

arrows, or the

rotary knob.

— Press

Enter

.

Averaging

Averaging helps to reduce the effects of random noise on a measurement. The
FieldFox computes the displayed value over several consecutive readings.
Average count determines the number of readings to average. The higher the
average count, the greater the amount of noise reduction.

An average counter is shown in the left edge of the screen as

Avg N

. This

shows the number of previous readings that have been averaged together.

When the counter reaches the specified count, then a ‘running average’ of the
last

N

readings is displayed.

Average count = 1 means there is NO averaging.

This setting can be changed at any time without affecting calibration accuracy.

How to set Averaging

— Press

Meas Setup 4

— Then

More

— Then

Avg N

where

N

is the current count setting.

— Enter a value using the numeric keypad. Enter

1

for NO averaging.

— Press

Enter

.

To restart the averaging process, press

Meas Setup 4

, then

More

, then

Restart

Single or Continuous Measure

This setting determines whether the FieldFox measures continuously or only
once each time the

Single

button is pressed. Use

Single

to conserve battery

power or to allow you to save or analyze a specific measurement.

«
...
164
165
166
167
168
...
»

Содержание N9923A





















































































































































































































































































Отзывы:

Нет отзывов