Keysight N9923A Скачать руководство пользователя страница 157

Страница: 157 / 276

Keysight N9923-90001 User’s Guide 157

Pulse Measurements Mode – Option 330
Pulse Measurement Settings

Auto Analysis

Auto Analysis reports the following TEN pulse measurements:

How to enable Auto Analysis

— Press

Mrk ->/Tools

— Then

Auto Analysis

— Then choose from the following:

—

OFF

Analysis OFF

—

The Analysis values appear below trace 1.

- Average Power

Average power level of all

measured data points

2 - Peak Power

Highest reading of all measured

data points

3 - Peak minus

Average

Difference between the above two

results

4 - Pulse Top

Power value based on the specified

Pulse Top setting.

5 - Rise Time

The time it takes for a pulse to rise

from 10% to 90% of its peak value.

6 - Fall Time

The time it takes for a pulse to fall

from 90% to 10% of its peak value.

7 - Pulse Width

The time between the rising edge

and falling edge of a pulse.

8 - Pulse Period

The time of one complete pulse cycle

9 - Duty Cycle

The ratio of the pulse width / pulse

period.

10 - Pulse Rep Freq

The rate, in pulses / sec, at which

pulses recur.

Содержание N9923A





















































































































































































































































































Результаты поиска

Содержание N9923A

Отзывы:

Keysight N9923A, Руководство пользователя, Страница: 157 / 276

Результаты поиска

Содержание N9923A

Отзывы: