manualshive.com logo in svg

Keysight N9923A, Руководство пользователя, Страница: 133 / 276

Поделиться
Скачать
Keysight N9923A Скачать руководство пользователя страница 133

Keysight N9923-90001 User’s Guide                                                                                                                      133

Power Meter (USB) Mode
USB Power Meter Settings

—

Single

 Automatically sets Continuous OFF and causes FieldFox to 

make ONE measurement, then hold for the next 

Single

 key press. 

When a data trace is displayed, the entire trace is measured, then 
holds. The 

Hold

 annotation changes to an arrow --> while the 

measurement occurs.

—

Continuous

 Makes continuous measurements. This is the typical 

setting when battery power is not critical.

You can also use 

Run / Hold +/-

 to toggle between Single and Continuous. 

Step Detection Mode

The FieldFox supports the Step Detection feature that is present in Keysight 
USB power sensors. When enabled, this feature reduces settling time after a 

significant step in the measured power. For more information, please refer to 
the USB Power Meter documentation.

How to set Step Detection mode

— Press 

Meas Setup 4

.

— Then 

Step Detection OFF ON

 

— Then choose from the following:

—

ON

 Enables step detection (default setting)

—

OFF

 Disables step detection

Limits

In Power Meter Mode, Minimum and Maximum limits set a visible range of 
acceptable readings between these two values. Readings that are below the 
minimum or above the maximum are clearly visible on the power meter display.

How to set Limits

— Press 

Limit 8

.

— Then choose from the following:

—

Min Limit OFF ON

 Toggles the display of the Minimum limit ON and 

OFF.

—

Min Limit Value

 Sets the Minimum limit power value. Power reading 

lower than this will exceed the limit.

—

Max Limit OFF ON

 Toggles the display of the Maximum limit ON and 

OFF.

—

Max Limit Value

 Sets the Maximum limit power value. Power reading 

higher than this will exceed the limit.

Содержание N9923A





















































































































































































































































































Отзывы:

Нет отзывов