Keysight N9923A Скачать руководство пользователя страница 132

Страница: 132 / 276

132 Keysight N9923-90001 User’s Guide

Power Meter (USB) Mode
USB Power Meter Settings

Resolution

Resolution sets the number of digits to display after the decimal point on the
digital power meter display.

How to set Resolution

— Press

Scale / Amptd.

— Then

More

— Then, in

Resolution

, choose from 0, 1, 2, or 3.

Averaging

Averaging is used to improve measurement accuracy in low power or noisy

power situations. Increased averaging improves measurement accuracy, but
also reduces measurement speed.

How to set Power Meter Averaging

— Press

BW 2

Meas Setup 4

— Then choose from the following:

—

Averaging Auto Man Off

—

Auto

Allows the USB Power Sensor to use its Auto Averaging

settings. See the USB Power Sensor documentation for details.

—

Man

Manually enter an averaging count by setting

Num Averages

—

OFF

Performs NO averaging.

—

Num Averages

Sets the number of Power Meter readings to be

averaged before a valid reading is displayed. When the number is

changed,

Averaging

is automatically set to Man.

Single or Continuous Measure

This setting determines whether the FieldFox measures continuously or only
once each time the

Single

button is pressed. Use

Single

to conserve battery

power or to allow you to save or analyze a specific measurement.

This setting can be changed at any time without affecting calibration accuracy.

How to set Single or Continuous

— Press

Sweep 3

— Then choose one of the following:

Содержание N9923A





















































































































































































































































































Результаты поиска

Содержание N9923A

Отзывы:

Keysight N9923A, Руководство пользователя, Страница: 132 / 276

Результаты поиска

Содержание N9923A

Отзывы: