Keysight N5247-60106 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 54

background image

52 Installation Note N5247-90106

Installation Procedure for the Upgrade

-

7. Repeat steps 3-6 to enable Option 419, clicking

419 - Src/Rcvr Atten &

Bias Ts 4-Port

in step 3.

8.

When the installation is complete, click

Exit

.

Option Verification Procedure

Once the analyzer has restarted and the Network Analyzer program is again

running:

1. On the analyzer’s Help menu, click About Network Analyzer.
2. Verify that “P04” and “419” are listed, but “219” is not listed after

“Options:” in the display. Click

OK

.

Step 55. Perform Post-Upgrade Adjustments and Calibration

Adjustments

The following adjustments must be made due to the hardware changes of the

analyzer.

— EE default adjustment
— synthesizer bandwidth adj. (only run when EE default adjust is not

sufficient)

— source adjustment
— IF gain adjustment
— receiver adjustment
— receiver characterization
— IF Response Adjustment (Option 090 Only)
— Noise Adjustment (Option 029 Only)
These adjustments are described in the PNA Service Guide and in the PNA

on-line HELP. A list of equipment required to perform these adjustments is also

found in the service guide.
To view this service guide information, click the Chapter 3 bookmark “Tests
and Adjustments” in the PDF Service Guide

1

.

After the specified adjustments have been performed, the analyzer should

operate and phase lock over its entire frequency range.

If the options have not been enabled or if the option 219 license has not

been removed,perform the prior steps again. If the option is still not

correct, contact Keysight Technologies. Refer to

“Getting Assistance from

Keysight” on page 4

.

1. See

“Downloading the Online PNA Service Guide” on page 6

.

«
...
50
51
52
53
54
»

Содержание N5247-60106























































Отзывы:

Нет отзывов

Похожие инструкции для N5247-60106

Бренд: X-Rite Страницы: 80

DigitalFlow XMT868i

Бренд: Panametrics Страницы: 74

Бренд: Bante Instruments Страницы: 6

Бренд: R.M. Young Страницы: 2

Бренд: janitza Страницы: 6

Бренд: janitza Страницы: 36

PowerCross-Laser 8 S

Бренд: LaserLiner Страницы: 64

ClimaHome-Check Plus

Бренд: LaserLiner Страницы: 10

MeterMaster Plus

Бренд: LaserLiner Страницы: 104

Бренд: LaserLiner Страницы: 52

LaserRange-Master T2

Бренд: LaserLiner Страницы: 52

Бренд: LaserLiner Страницы: 5

CombiRangeXtender 40

Бренд: LaserLiner Страницы: 84

SuperCross-Laser 2P

Бренд: LaserLine Страницы: 92

MoistureFinder Compact

Бренд: LaserLine Страницы: 56

LaserRange-Master Gi7 Pro

Бренд: LaserLiner Страницы: 56

Бренд: Laser Tools Страницы: 4

SmartVision-Laser

Бренд: LaserLiner Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды