Keysight N5247-60106 Скачать руководство пользователя страница 49

Страница: 49 / 54

Installation Note N5247-90106 49

Installation Procedure for the Upgrade

3. In the section “Removing the Power Switch Board and Power Button

Keypad,” perform only step 1.

4. Remove the braided gasket from the backside edges of the 2-port front

frame and install it in the 4-port front frame.

Reassemble the front panel assembly with the new 4-port front frame

(N5247-20141) by reversing the order of the instructions previously
followed.

Step 46. Reinstall Front Panel Assembly

For instructions on reinstalling the front panel assembly, click the Chapter 7

bookmark “Removing and Replacing the Front Panel Assembly” in the PDF
Service Guide

Step 47. Install the Overlays and Nameplate

To see an image of the front panel overlay (N5247-80011), keypad overlay

(N5242-80005), power button overlay (N5242-80007), and nameplate

(N5247-80006), click the Chapter 6 bookmark “Front Panel Assembly, Front
Side, All Options” in the PDF Service Guide

. New parts are listed in

Table 1 on

page 8

Remove the protective backing from the new front panel overlay

(N5247-80011).

Loosely place the overlay in the recess on the lower front panel.

Placing two fingers at the middle, press the overlay firmly onto the frame

while sliding your fingers in opposite directions towards the ends of the

overlay. Repeat on all areas of the overlay.

Repeat steps 1-3 to install the keypad overlay (N5242-80005).

Repeat steps 1-3 to install the power button overlay (N5242-80007).

Install the new nameplate (N5247-80006).

Step 48. Install the Jumper Cables

Install twelve W60 front panel jumper cables (N5247-20107) - use 6 new

jumpers and reuse 6 old jumpers. To see an image of the front panel jumper

cables, click the Chapter 7 bookmark “Removing and Replacing the Front
Panel Assembly” in the PDF Service Guide

Step 49. Position the Cables and Wires to Prevent Pinching

On the top side of the PNA, carefully position the grey flex cables so they can’t

be pinched between the covers and the rails.

Содержание N5247-60106























































Результаты поиска

Содержание N5247-60106

Отзывы:

Похожие инструкции для N5247-60106

Бренды по названию

Популярные бренды

Keysight N5247-60106, Установочная инструкция

Результаты поиска

Содержание N5247-60106

Отзывы:

Похожие инструкции для N5247-60106

Бренды по названию

Популярные бренды