manualshive.com logo in svg

Keysight N5247-60106, Установочная инструкция

Поделиться
Скачать
Keysight N5247-60106 Скачать руководство пользователя страница 41

Installation Note N5247-90106                                                                                                                                  41

Installation Procedure for the Upgrade

Semirigid Cables Required for Upgrading to an Option 419 PNA

To see images showing the location of these cables, click the Chapter 6 
bookmark “Bottom RF Cables, 4-Port, Option 419” in the PDF Service Guide

1

. 

New parts are listed in 

Table 1 on page 8

.

— W69 (reuse) (N5247-20112)  A27 mixer brick to rear-panel EXT TSET DRIVE 

LO OUT (J5)

— W68 (N5247-20088) rear panel port RF2 OUT (J12) to W67

 

 

 * Install SMA load previously removed from A10 26.5 GHz source board 

onto rear panel port RF2 OUT (J12).

 

— W123 (reuse) (N5247-20020) A49 port 2 receiver attenuator to port 2 RCVR 

B IN

— W115 (reuse) (N5247-20027) A45 port 2 bias tee to port 2 CPLR THRU 
— W46 (N5247-20019) A36 port 2 coupler to port 2 CPLR ARM
— W114 (reuse) (N5247-20034) A41 port 2 source attenuator to port 2 

SOURCE OUT

— W112 (N5247-20029) A44 port 4 bias tee to A35 port 4 coupler
— W124 (reuse) (N5247-20046) A49 port 2 receiver attenuator to A27 mixer 

brick (B)

— W146 (reuse) (N5247-20058)  A32 port 2 reference coupler to REF 2 

SOURCE OUT

— W145 (N5247-20066)  A27 mixer brick (R2) to REF 2 RCVR R2 IN

* As shown in 

Figure 26

, install clamp part number 1400-1334 to secure 

W145.

1. See 

“Downloading the Online PNA Service Guide” on page 6

.

Содержание N5247-60106























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды