manualshive.com logo in svg

Keysight N5244AU- H29, Установочная инструкция

Поделиться
Скачать
Keysight N5244AU- H29 Скачать руководство пользователя страница 18

Installation Note N5245-90109                                                                                                                                  17

Keysight Extended Power Range and Bias Tees 
Upgrade Kit Order Numbers: N5244AU-921 and N5245AU-921

Step 8.Remove Some Existing Cables

1.

Place the analyzer bottom-side up on a flat surface.

2.

Remove the following cables in the order listed. These two cables may be 

discarded - they will not be reinstalled. 

 

To see an image showing the location of these cables, click either the 

Chapter 6 bookmark “4-Port Configuration, Options 400/419/423” or 

“4-Port Configuration, Options 400/419/423/H85” in the PDF Service 
Guide

1

. 

— W82 (N5245-20077) A38 port 1 source attenuator to front-panel Port 1 

SOURCE OUT

— W58 (N5245-20095) A28 mixer brick to 50 ohm load 
Option 400/419/423 only:

1.

Remove the following cables in the order listed. These three cables may 

be discarded - they will not be reinstalled. 

 

To see an image showing the location of these cables, click the Chapter 6 

bookmark “4-Port Configuration, Options 400/419/423” in the PDF Service 
Guide

1

. 

—    W96 (N5245-20087) A45 port 2 bias tee to front-panel Port 2 CPLR THRU 
—    W84 (N5245-20085) A42 port 1 bias tee to front-panel Port 1 CPLR THRU 
Option 400/419/423/H85 only:

1.

Remove the following cables in the order listed. These two cables may be 

discarded - they will not be reinstalled. 

 

To see an image showing the location of these cables, click the Chapter 6 

bookmark “4-Port Configuration, Options 400/419/423/H85” in the PDF 
Service Guide

1

. 

— W20 (N5245-20099) Front panel port 1 CPLR THRU to A33 port 1 coupler
—    W32 (N5245-20097) Front panel port 2 CPLR THRU to A36 port 2 coupler

Be careful not to damage the center pins of the semirigid cables. Some 

flexing of the cables may be necessary but do not over-bend them.

Содержание N5244AU- H29











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды