Keysight N5227B Скачать руководство пользователя страница 43

Страница: 43 / 415

Keysight N5227B Service Guide 3-17

Tests and Adjustments
Preliminary Checks

Figure 3-6

Typical Cable Insertion Loss Response

If the Cable Insertion Loss Check Fails

Clean the cable and devices and torque to specification. Repeat the check.

If the check still fails, the cable should be repaired or replaced.

Cable Magnitude and Phase Stability Check

With the test port cable still connected to Port 1, connect a short to the

other end of the cable.

Press UTILITY

Press TRACE/CHANNEL

, then

. In the New Trace

dialog box, click the S11 box, and then click OK.

Press RESPONSE

, then

, then ENTRY

Press RESPONSE

. Verify that

is ON. If not, press

the

softkey to toggle it ON.

The Averaging Factor box will appear directly above the display. In the

Averaging Factor box, type 50 or click the arrows to select 50, and then
press ENTRY

Preset

Traces

New Trace

...

Format

Phase

Enter

Avg

Average ON/off

Average on/OFF

Enter

Содержание N5227B
































































































































































































































































































































































































































Результаты поиска

Содержание N5227B

Отзывы:

Похожие инструкции для N5227B

Бренды по названию

Популярные бренды

Keysight N5227B, Руководство по обслуживанию

Результаты поиска

Содержание N5227B

Отзывы:

Похожие инструкции для N5227B

Бренды по названию

Популярные бренды