Keysight N5227B Скачать руководство пользователя страница 41

Страница: 41 / 415

Keysight N5227B Service Guide 3-15

Tests and Adjustments
Preliminary Checks

Figure 3-4

Typical Cable Return Loss Response

If the Cable Return Loss Check Fails

Clean the cable and devices and torque to specification. Repeat the check.

If the check still fails, the cable should be repaired or replaced.

Cable Insertion Loss Check

Press UTILITY

Press STIMULUS

, then

, and set to 801.

Press RESPONSE

, then

, and set the IF

Bandwidth to 30 Hz.

Press STIMULUS

and set the power level to -17 dBm.

Perform a 1-port calibration on the PNA Port 1 using SmartCal (Guided

Calibration). Follow the calibration wizard instructions. After calibration,

the PNA prompts you to save the cal set as a user Calset. Save the cal set

data as CalSet_1.cst.

Connect the test port cable to the PNA Port 1 and perform a 1-port

calibration again at the end of the cable. After calibration, save the cal set

data as CalSet_2.cst.

The method below runs on the PNA environment using a mechanical Cal

kit. An appropriate ECal could be used as well to replace the mechanical

Cal kit if desired.

Preset

Sweep

Number of Points

Avg

IF Bandwidth

Power

Содержание N5227B
































































































































































































































































































































































































































Результаты поиска

Содержание N5227B

Отзывы:

Похожие инструкции для N5227B

Бренды по названию

Популярные бренды

Keysight N5227B, Руководство по обслуживанию

Результаты поиска

Содержание N5227B

Отзывы:

Похожие инструкции для N5227B

Бренды по названию

Популярные бренды